Last run of goods for September. As always there are a number of new
to the list solid user and collectible tools.
PayPal is preferred (if you use it) on all items. It's easier for me to
ship items off of a paid PayPal invoice, especially First Class ones.
Checks and money orders are still welcome.
And remember........da more ya buy, the cheaper they fly!
First contact (that is e-mail, or phone) that says I want it gets it.
Prices do not include shipping. All items are shipped with Delivery
Confirmation. Insurance, unless it is a big order or a very fragile item
is optional. Just let me know. Also, I am shipping a lot more stuff via
First Class mail. There will be a small amount added to the shipping
cover the cost of the padded mailer. I don't get them for free.
Please put your name and address in the message. Saves time and email
traffic!
---------------------------------------------------
A Complete Set Of Millers Falls No 106 Carving Tools & Box. This all
weighs 10 1/2 oz unboxed. The tools are in good condition and were
lightly cleaned. All the blades are good save for a little staining on
the back of C skew chisel and one tiny dot of pitting on the inside of
the E gouge sweep. The handle finish on all of them is near perfect
other than a little light funky. The box is in fair condition. That
has some old tape repairs to the lid and bottom and the paper covering
is worn in a few spots. There are some light doodles on the inside of
the lid. These ain't pristine, but they sure ain't bad, and these
complete sets are sure getting few and far between, at least around
here. $35.00
http://oldetoolshop.com/forsale/sept/carvingtoolset0901a.jpg
http://oldetoolshop.com/forsale/sept/carvingtoolset0901b.jpg
http://oldetoolshop.com/forsale/sept/carvingtoolset0901c.jpg
http://oldetoolshop.com/forsale/sept/carvingtoolset0901d.jpg
http://oldetoolshop.com/forsale/sept/carvingtoolset0901e.jpg
http://oldetoolshop.com/forsale/sept/carvingtoolset0901f.jpg
Genuine Plumb Hammer Poll Carpenters Adze Head . Measuring 10 1/2" long
(straight across), the edge is 4 1/2" wide, and this weighs 2 lbs 10 1/4
oz unboxed. This is in decent condition and was cleaned. There is some
overall light pitting and patina going. The blade has some light
pitting and frosting. The edge is fairly good save for one small chip.
The sides are slightly beveled there, but that's how this guy was made.
The hammer poll is good. The eye has a little funky on the side, but
it's solid with no cracks. This ain't the prettiest, but it is a
quality tool that will get the job done. $32.00
http://oldetoolshop.com/forsale/sept/adze0901a.jpg
http://oldetoolshop.com/forsale/sept/adze0901b.jpg
http://oldetoolshop.com/forsale/sept/adze0901c.jpg
http://oldetoolshop.com/forsale/sept/adze0901d.jpg
http://oldetoolshop.com/forsale/sept/adze0901e.jpg
Vintage Cast Iron E C Stearns Style File Handle. Measuring 4 15/16"
long and this weighs 4 1/2 oz unboxed. Not signed as to the maker.
This is in reasonably good condition and was cleaned. There is some wear
to the finish and it's down to about 50%. The webbing is good with no
cracks. The clamp and screw are good, the screw doesn't come all the
way out (common problem with these guys), but it closes tight. This
ain't minty but it's better than most of these that I have been seeing
lately. $22.00
http://oldetoolshop.com/forsale/sept/filehandle0901a.jpg
http://oldetoolshop.com/forsale/sept/filehandle0901b.jpg
Vintage Erie Tool Works 4 lb Stone Mason Hammer Head. Measuring 5"
long, the faces are 1 7/16" square, and this weighs 3 lbs 15 1/2 oz
unboxed. The Erie Tool Works was founded in 1902 and continued working
under that name until 1959. This is a forged head. This is in decent
condition and was cleaned. There is some overall light patina. Both
faces have some dings and wear and the one has a small chip on the one
side. The punched eye has some crusty on the inside and some dinging on
the inside at the top, but it's solid. This ain't pristine, but it's a
solid tool that still will get the job done. $18.00
http://oldetoolshop.com/forsale/sept/hammer0912a.jpg
http://oldetoolshop.com/forsale/sept/hammer0912b.jpg
http://oldetoolshop.com/forsale/sept/hammer0912c.jpg
http://oldetoolshop.com/forsale/sept/hammer0912d.jpg
Warwood Bell System 3 lb Straight Peen Linesman Hammer. Measuring 15
5/8" overall, the head is 5 13/16" long, the face is 1 3/8" in diameter,
the peen is 1 9/16" high, and this weighs 3 lbs 12 oz unboxed. Warwood
is a Wheeling WV hammer and tool maker. The Bell System was broken up
back in 1982 and my guess is that this is from the 1970's. This is in
reasonably good condition and was cleaned. These guys were never
finished off real pretty like to start with. There is some either
pitting or corrosion on the top back by the peen. The face is good
other than some dings. The peen is also good save for a little wear at
the top. The handle looks to be original to the top. That does have
some roughness under the eye, but unless you are one of those fools who
couldn't hit the broad side of a barn with a bulldozer, that won't be a
problem. There are also some dings and few tiny bits of paint. The head
is on tight, at least setting here. This ain't minty, but it's a
quality tool that will get the job done. $20.00
http://oldetoolshop.com/forsale/sept/hammer0914a.jpg
http://oldetoolshop.com/forsale/sept/hammer0914b.jpg
http://oldetoolshop.com/forsale/sept/hammer0914c.jpg
http://oldetoolshop.com/forsale/sept/hammer0914d.jpg
Vintage Plumb Wood Hewing Hatchet Or Axe. Measuring 15" overall, the
head is 5 13/16" long (across the center), the edge is 4 7/16" high
(straight across), and this weighs 2 lbs 5 oz unboxed. This is in
decent condition and was cleaned. The head has some overall frosting,
some spots of light pitting, and some dings. The back has some frosting
in the working area, but nothing too bad. The edge is fairly good save
for one chipped spot. The poll does have some chipping all around. The
eye is good with no cracks that I can see. The handle is old and might
be the original one. That has some dings and stains, but it's solid,
and the head is on tight. This ain't pristine, but it's a quality tool
that will get the job done. $45.00
http://oldetoolshop.com/forsale/sept/axe0905a.jpg
http://oldetoolshop.com/forsale/sept/axe0905b.jpg
http://oldetoolshop.com/forsale/sept/axe0905c.jpg
http://oldetoolshop.com/forsale/sept/axe0905d.jpg
http://oldetoolshop.com/forsale/sept/axe0905e.jpg
Vintage Small Brass Head Ball Peen Hammer. Measuring 4 3/4" overall,
the head is 1 1/2" long, the face is 11/16" in diameter, the peen is
5/8" in diameter, and this weighs 6 oz unboxed. Not signed as to the
maker. This is in decent condition and was cleaned. There are some
dings on the sides of the head. The face and peen both have some
overall dinging and I did run a file over some mushrooming around the
face. The steel handle is good save for some frosting. The head
wiggles a touch, but does not come off. This ain't the prettiest, but
it's a neat little hammer that will get the job done. $15.00
http://oldetoolshop.com/forsale/sept/hammer0910a.jpg
http://oldetoolshop.com/forsale/sept/hammer0910b.jpg
http://oldetoolshop.com/forsale/sept/hammer0910c.jpg
http://oldetoolshop.com/forsale/sept/hammer0910d.jpg
Vintage Lignum Vitae Plumbers Lead Pipe Flaring Egg. Measuring 4" long,
2 7/8" in diameter, and this weighs 8 1/2 oz unboxed. Not signed as to
the maker. This is in reasonably good condition and was cleaned. There
are a few dings and some wear, but overall nothing too bad. The top
also has some dings and the tip is good. This ain't minty, but these
Lignum ones are sure getting hard to come by, at least around here. $18.00
http://oldetoolshop.com/forsale/sept/leadtool0802a.jpg
http://oldetoolshop.com/forsale/sept/leadtool0802b.jpg
http://oldetoolshop.com/forsale/sept/leadtool0802c.jpg
Moore & Wright No 825B Centre Finder. Measuring 5 1/2" long, 2 15/16"
high, and this weighs 3 1/2 oz unboxed. This is in reasonably good
condition and was cleaned. There are a few spots of light patina, but
overall nothing too bad. The edges are crispy and the notch is good
with no wear. This ain't pristine, but it is a quality tool that will
get the job done. $30.00
http://oldetoolshop.com/forsale/sept/machinisttool0912a.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0912b.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0912c.jpg
Early Hand Forged 3/4 lb Cross Peen Hammer Head. Measuring 3 15/16"
long, the face is 11/16" wide, 7/8" high, the peen is 1" wide, and this
weighs 12 1/2 oz unboxed. Not signed as to the maker. This is in
decent condition and was cleaned. Somebody else dressed the face and
peen. There is some overall patina on the body. The face has some
scuffs, but is good as is the peen. The square punched eye has a little
crusty on the inside, but it's solid. This ain't minty, but then tools
of this age and use, rarely are. $17.00
http://oldetoolshop.com/forsale/sept/earlyhammer0901a.jpg
http://oldetoolshop.com/forsale/sept/earlyhammer0901b.jpg
http://oldetoolshop.com/forsale/sept/earlyhammer0901c.jpg
Vintage Brass Frame Mill Utility Layout Knife. The handle is 4 9/16"
long, the metal insert is 8 3/8" long, 9/16" wide, and this weighs 7 1/2
oz unboxed. The body isn't signed as to the maker, the insert is an R.
Murphy. This is in reasonably good condition and was cleaned. The
brass has some light scuffs and wear. Both screws work. The handle
scales are some kind of man made material, possibly Bakelite. They also
has some light dings and scuffs, but are on tight. The steel insert
also has some light patina, but nothing too bad. The edge will need
some work. This ain't pristine, but it's a solid tool that will get the
job done. $35.00
http://oldetoolshop.com/forsale/sept/knife0902a.jpg
http://oldetoolshop.com/forsale/sept/knife0902b.jpg
http://oldetoolshop.com/forsale/sept/knife0902c.jpg
http://oldetoolshop.com/forsale/sept/knife0902d.jpg
Products Engineering No PEC 7072 Steel 6 Ft Zig Zag Folding Rule. this
weighs 8 1/2 oz unboxed. This is in reasonably good condition and was
not cleaned. The segments are all clean except for one small spot of
rust. All the rulings are readable and the edges are good. The one end
joint is a little loose, but the rest hold tight. This ain't pristine,
but if that's what you want, new ones are still out there for $120.
Look it up. $20.00
http://oldetoolshop.com/forsale/sept/rule0902a.jpg
http://oldetoolshop.com/forsale/sept/rule0902b.jpg
http://oldetoolshop.com/forsale/sept/rule0902c.jpg
http://oldetoolshop.com/forsale/sept/rule0902d.jpg
J H Weil Philadelphia USCE 8 Inch Proportional Divider & Case. The tool
is 8 1/16" long and this all weighs 6 1/2 oz unboxed. The case and the
tool are also marked U.S.C.E. which stands for the United States Army
Corps of Engineers. This is in good condition and was not cleaned. The
arms have a few tiny dings and there are some light scuffs on the
insides, but overall nothing too bad. All of the tips were blued and
those are good as well. The adjuster works just like it should. The
case is good with no wear and the latch works. This is a great
collectible and very classy user tool as well. $45.00
http://oldetoolshop.com/forsale/sept/draftingtool0901a.jpg
http://oldetoolshop.com/forsale/sept/draftingtool0901b.jpg
http://oldetoolshop.com/forsale/sept/draftingtool0901c.jpg
http://oldetoolshop.com/forsale/sept/draftingtool0901d.jpg
L S Starrett No 92 9 Inch Divider. Measuring 9 1/2" long (from the tips
to the top of the joint) and this weighs 8 1/4 oz unboxed. This is in
reasonably good condition and was cleaned. There is a little frosting,
but nothing too bad. The joint is good. The locking screw and the fine
adjuster nut work. The inside nut on the fine adjuster arm moves a
little slow, but I did have it all the way off. Both tips are good as
is the clamp on the removable tip. This ain't pristine, but it sure
ain't bad, and it will get the job done for a whole lot less than a new
one will cost you. $75.00
http://oldetoolshop.com/forsale/sept/machinisttool0914a.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0914b.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0914c.jpg
Small Belgian Coticule Sharpening Stone Or Hone. Measuring 4 7/8" long,
1 3/16" wide, 9/16" high, and this weighs 6 1/4 oz unboxed. This is in
reasonably good condition and was lightly cleaned. The face has some
stains, some natural grain lines, and a little wear. There is very
slight dip in the center looking from the side (like 1/32"). Looking
from the ends it's fairly straight. There are some tiny chips on the
edges. The base has some light scuffs. This ain't minty, but it's an
older tool that will get the job done. $45.00
http://oldetoolshop.com/forsale/sept/sharpeningstone0903a.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0903b.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0903c.jpg
TWO Mahogany Cased Slip Sharpening Stones. The case on the left is 5
3/8" long, 2 11/16" wide, 1 5/16" high, the one on the left is 5 1/8"
long, 3 3/16" wide, 1 1/2" high, and this all weighs 1 lb 5 oz total
unboxed. There is a user name stamped on the left one, but there are
not other marks on the cases and stones. These are in reasonably good
condition and were cleaned. The lighter stone feels like a fine or
extra fine and might be an Arkansas stone. That measures 4 11/16" long,
2" high, 7/16" wide at the top, and 5/32" at the lower end. The gray
stone feels like a medium grit. That measures 4 1/2" long, 2 1/8" high,
5/8" wide at the top, and 5/16" at the lower end. Both stones have some
stains. The lighter stone does have a little wear in the center along
the top and lower edge. The edges on the gray stone are good. The case
on the left has some staining and dings. The other case has some light
yellow paint on the inside of the left and on the inside of the base.
Both have a brad showing where they were repaired at some point, but
both are solid. These ain't pristine, but I really doubt that you are
going to see another set like this any time soon, I sure have not. $55.00
http://oldetoolshop.com/forsale/sept/sharpeningstone0902a.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0902b.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0902c.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0902d.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0902e.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0902f.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0902g.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0902h.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0902i.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0902j.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0902k.jpg
Sandusky Tool No 47 1/4 Side Bead Molding Plane. This weighs 12 oz
unboxed. The mark is partially obscured by a user mark, but can be
read. This is in reasonably good condition and was cleaned. The body
has some stains and dings. The heel also has some dings and the same
user mark. The sole and boxing are good and the mouth is tight and was
never messed with. The cutting face of the iron is clean. The wedge
has a little wear on the edges, but it's solid. This ain't minty, but
these guys have sure been few and far between of late. $19.00
http://oldetoolshop.com/forsale/sept/woodenplane0902a.jpg
http://oldetoolshop.com/forsale/sept/woodenplane0902b.jpg
http://oldetoolshop.com/forsale/sept/woodenplane0902c.jpg
http://oldetoolshop.com/forsale/sept/woodenplane0902d.jpg
Vintage No 3 Hand Saw Sharpening Vise. The jaws are 9 5/8" wide and
this weighs 4 lbs 4 1/2 oz unboxed. Not signed as to the maker, this is
just marked No. 3. This is in decent condition and was cleaned. There
is some wear to the original finish, a few small bits of paint, and some
light patina where the finish is worn. The jaws are fairly good, but
don't close quite flush looking from the side. The frame is good with
no cracks and the clamp works. The bench clamp screw works as does the
pivot screw. This sure ain't the prettiest peach in the patch, but it's
a solid tool that will get the job done. $30.00
http://oldetoolshop.com/forsale/sept/sawvise0901a.jpg
http://oldetoolshop.com/forsale/sept/sawvise0901b.jpg
http://oldetoolshop.com/forsale/sept/sawvise0901c.jpg
http://oldetoolshop.com/forsale/sept/sawvise0901d.jpg
http://oldetoolshop.com/forsale/sept/sawvise0901e.jpg
Blacksmith 2 1/2 lb Cross Peen Hammer Head. Measuring 5 3/16" long, the
face is 1 3/8" in diameter, the peen is 1 1/2" wide, and this weighs 2
lbs 9 1/2 oz unboxed. Not signed as to the maker. This is in decent
condition and was cleaned. There is some overall light patina. The
face has some old chips around the edge. The peen is good save for a
small chip on the one side. The eye is good to go. This ain't pretty or
perfect, but drop it on a handle and it will get the job done. $15.00
http://oldetoolshop.com/forsale/sept/hammer0908a.jpg
http://oldetoolshop.com/forsale/sept/hammer0908b.jpg
http://oldetoolshop.com/forsale/sept/hammer0908c.jpg
http://oldetoolshop.com/forsale/sept/hammer0908d.jpg
Chapin-Stephens No 68 2 Ft Folding Rule. This weighs 1 1/2 oz unboxed.
This is in reasonably good condition and was not cleaned. The finish on
the outside is original, There is a little wear, but most of it is
present. The same goes for the inside. All the rulings are readable.
The brass has some staining. The inside pins are present, but the side
pin is missing. The one outer leg is slightly warped. The joints are
good. This ain't 100% minty, but it sure is in better condition than
most of these guys that I see. $17.00
http://oldetoolshop.com/forsale/sept/rule0901a.jpg
http://oldetoolshop.com/forsale/sept/rule0901b.jpg
http://oldetoolshop.com/forsale/sept/rule0901c.jpg
TWO Woodcraft Supply Cabinet Makers Turnscrews Or Screwdrivers. The one
on the left is 11 1/16" long, the tip is 7/16" wide, the other one is 16
1/8" long, the tip is 9/16" wide, and they weigh 1 lb 1 1/4 oz unboxed.
Made in Merry Olde England. These are in reasonably good condition and
were cleaned. The head on the smaller one has some light frosting, but
both tips are clean. The shafts ave some light roughness, but that's
how they were made. Both handles have some dings and stains, but are
solid. These ain't minty, but they will get the job done. $35.00
http://oldetoolshop.com/forsale/sept/turnscrew0905a.jpg
http://oldetoolshop.com/forsale/sept/turnscrew0905b.jpg
http://oldetoolshop.com/forsale/sept/turnscrew0905c.jpg
http://oldetoolshop.com/forsale/sept/turnscrew0905d.jpg
Vintage Early Cast Iron Pliers. Measuring 9 7/8" long, the jaws are
13/16" deep, 3/16" wide at the tips, and this weighs 1 lb 1 oz unboxed.
Not signed as to the maker. This is in decent condition and was
cleaned. There is some areas of light pitting. The jaws are good. The
lap joint has a little play, but the rivet is good. I'm thinking that
this was used for lifting small crucibles, but I could be wrong on
that. But, I sure ain't seen too many of these guys around. $18.00
http://oldetoolshop.com/forsale/sept/pliers0901a.jpg
http://oldetoolshop.com/forsale/sept/pliers0901b.jpg
http://oldetoolshop.com/forsale/sept/pliers0901c.jpg
Vintage 1 lb Turned Steel Turnip Plumb Bob. Measuring 2 13/16" long, 1
7/8" in diameter, and this weighs 15 1/2 oz unboxed. Not signed as to
the maker. This is in reasonably good condition and was cleaned. There
is a little frosting, but nothing too bad patina wise. The tip is
good. The brass string cap is also good and removes completely. This
ain't gotta fancy maker's name, but it's a good looking tool to say the
least. $25.00
http://oldetoolshop.com/forsale/sept/plumbbob0902a.jpg
http://oldetoolshop.com/forsale/sept/plumbbob0902b.jpg
http://oldetoolshop.com/forsale/sept/plumbbob0902c.jpg
Stanley No 20 1 1/4 Inch Everlasting Chisel. Measuring 5 5/16" from the
edge to the top of the ferrule, the blade is 4 3/16" long, this is 10
9/16" overall, and this weighs 12 oz unboxed. This is in fair condition
and was cleaned. The back has some overall light pitting, a few spots
of deeper pitting, and a few scuffs. The top also has more of the
same. The sides have some dings and I did run a file over some
mushrooming down by the ferrule. The edge will need some work. The
ferrule has some dings, but no cracks that I can see. The handle has
some wear, a partial check on the front, and a sliver off of the back.
The striking button has lots of dings. This ain't the prettiest, but
then these bigger sizes sure ain't getting any easier to find. $28.00
http://oldetoolshop.com/forsale/sept/chisel0903a.jpg
http://oldetoolshop.com/forsale/sept/chisel0903a.jpg
http://oldetoolshop.com/forsale/sept/chisel0903a.jpg
EasyCut USA 8 Inch Draw Knife Or Drawknife. Measuring 14 1/2" overall,
the blade is 7 15/16" long, 1 1/2" wide across most of the edge, 1 7/16"
at one end. and this weighs 1 lb 1/2 oz unboxed. This was a hardware
store brand name, but which one seems to be lost to history. This is in
reasonably good condition and was cleaned. The back has some very light
frosting, but nothing too bad. The top has some dings and I did run a
file over some mushrooming on the top. The edge has a few dings and
will need a little work. The front also has some frosting and light
patina. Both handles have most of the original finish. There is a
little wear and few tiny bits of paint. The left one wiggles a hair.
The end caps and ferrules also good save for a little frosting. This
ain't minty, but it will get the job done. $38.00
http://oldetoolshop.com/forsale/sept/drawknife0901a.jpg
http://oldetoolshop.com/forsale/sept/drawknife0901b.jpg
http://oldetoolshop.com/forsale/sept/drawknife0901c.jpg
Early Hand Forged Grubbing Pick Head (I said PICK HEAD, turn up yer
hearing aid!) Measuring 12 3/4" long, the vertical end is 1 13/16"
high, the other end is 1 3/4" wide, and this weighs 2 lbs 11 3/4 oz
unboxed. Not signed as to the maker, there are user initials chisel
marked on the one side. This is in decent condition and was cleaned.
This has a wrought iron body with steel bits on both ends. There is
some overall pitting and patina. The bit on the vertical end is small,
but still can be see. The bit on the other end has some wear and a
little chipping. The eye has some crusty on the inside and the forge
weld line is open a bit at the one end.. This ain't the prettiest, but
these older guys sure haven't been showing up much at all, at least
around here. $24.00
http://oldetoolshop.com/forsale/sept/hfpickhead0901a.jpg
http://oldetoolshop.com/forsale/sept/hfpickhead0901b.jpg
http://oldetoolshop.com/forsale/sept/hfpickhead0901c.jpg
http://oldetoolshop.com/forsale/sept/hfpickhead0901d.jpg
Stanley Type 3 1897 Patent 10 inch Adjustable Bevel Square. This weighs
6 1/2 oz unboxed. This is a Type 3 and was made by Stanley between 1898
and 1903. Justus A. Traut of New Britain, CT was granted Design Pat.
No. D26,768 on Mar. 16, 1897 for the design of this tool. This is in
reasonably good condition for being at least 120 years old and was
cleaned. The blade has some spots of frosting and there are some spots
of light pitting around the slot. The edges and corners are good. The
rosewood handle has some wear, dings, and some small user initials
stamped on the lower front. The locking screw does it's job. This
ain't minty, but Then tools of this age rarely are, and it will get the
job done. $19.00
http://oldetoolshop.com/forsale/sept/square0902a.jpg
http://oldetoolshop.com/forsale/sept/square0902b.jpg
http://oldetoolshop.com/forsale/sept/square0902c.jpg
http://oldetoolshop.com/forsale/sept/square0902d.jpg
Small Hand Forged Slater Slate Splitting Chisel. Measuring 6 3/8" long,
the edge is 1 15/16" wide, and this weighs 5 oz unboxed. Not signed as
to the maker. This is in reasonably good condition and was cleaned.
There is some frosting and a few spots of light pitting, but nothing too
bad. The edge is good and was dressed recently. There is some light
mushrooming on the sides. The striking button has some light dings, but
no cracks that I can see. I gotta say, that these small ones are sure
getting hard to find and especially in this kind of shape. $19.00
http://oldetoolshop.com/forsale/sept/slatetool0901a.jpg
http://oldetoolshop.com/forsale/sept/slatetool0901b.jpg
http://oldetoolshop.com/forsale/sept/slatetool0901c.jpg
W Johnson Newark NJ Plated Rosewood Mortising Gage Or Gauge. This
weighs 9 oz unboxed. This is in good condition and was cleaned. The
beam is good other than having a user name marked on both sides. The
brass plate on the beam has some light wear. The points could stand a
touch up, but there is lots to work with. The adjuster works and was
oiled. The head also has the same name stamped on it. The brass face
is good and the locking screw works and has the small brass shoe on the
inside. This is not a very commonly found tool by this or any other
American maker. $45.00
http://oldetoolshop.com/forsale/sept/mortisegage0901a.jpg
http://oldetoolshop.com/forsale/sept/mortisegage0901b.jpg
http://oldetoolshop.com/forsale/sept/mortisegage0901c.jpg
http://oldetoolshop.com/forsale/sept/mortisegage0901d.jpg
http://oldetoolshop.com/forsale/sept/mortisegage0901e.jpg
Early 19th Century Wooden Smoothing Plane. The beech body is 7 9/16"
long, 2 15/16" wide, 2 1/2" high at the toe, the iron is 2 5/16" wide
across the edge, and this weighs 1 lb 13 1/4 oz unboxed. The body isn't
signed and the iron is marked J Smith, which could be either Joseph or
John, both of whom worked in the early 1800's in Sheffield England.
This is in decent condition and was cleaned. The body has some stains,
dings, and some checks on the toe and heel. The sole has some wear in
the center, along with much stains and dings, and a few of the checks
travel down there as well. The mouth is opened from wear. The wedge is
oak and looks to be original to the tool. That is good other than some
stains. The iron is fairly clean on the steel face, save for some
frosting and a few spots of light pitting. The iron body does have some
deeper pitting and some mushrooming at the top. This ain't minty, but
considering the age of the tool and how hard these guys got used, this
one sure ain't bad. $65.00
http://oldetoolshop.com/forsale/sept/earlyplane0901a.jpg
http://oldetoolshop.com/forsale/sept/earlyplane0901b.jpg
http://oldetoolshop.com/forsale/sept/earlyplane0901c.jpg
http://oldetoolshop.com/forsale/sept/earlyplane0901d.jpg
http://oldetoolshop.com/forsale/sept/earlyplane0901e.jpg
Stanley No 261 3/16 Inch Phillips Screwdriver Brace Bit. The tip is
3/16" in diameter and this weighs 1 oz unboxed. This is in reasonably
good condition and was cleaned. The tip has a little wear, but there is
plenty to work with. The shaft is good and the mark and patent dates
are readable. The tang is also good. This ain't pristine, but these
guys are sure getting few and far between. $15.00
http://oldetoolshop.com/forsale/sept/bracetool0901a.jpg
http://oldetoolshop.com/forsale/sept/bracetool0901b.jpg
Small Vintage 3 oz Straight Peen Hammer. Measuring 10" overall, the
head is 3 1/8" long, the face is 1/2" in diameter, the peen is 1/2"
high, and this weighs 3 3/4 oz total unboxed. Not signed as to the
maker. This is in decent condition and was cleaned. There is some
pitting on the head. The face has some very light pitting and a small
chip on the underside. The peen has some wear on the ends, but it's
good otherwise. The handle looks to be original. That has a check under
the eye, some dings, stains, and there is a slice missing off of the
back. The handle feels solid enough, as long as you don't try to drive
framing nails with this guy. Just saying. This ain't pretty or
perfect, but these guys sure do not show up very often. $18.00
http://oldetoolshop.com/forsale/sept/hammer0906a.jpg
http://oldetoolshop.com/forsale/sept/hammer0906b.jpg
http://oldetoolshop.com/forsale/sept/hammer0906c.jpg
Vintage Cast Iron Saw FIler Or Jointer. The body is 4" long, the file
is 5" long, and this weighs 9 oz unboxed. Not signed as to the maker,
this is just marked Made In USA. This is in decent condition and was
cleaned. The body has some wear to the original finish and there is a
little funky on there as well. All the screws work. The file has some
wear on both sides and some light rust, but there still is some left to
work with. This ain't pristine, but this guy will get the job done. $25.00
http://oldetoolshop.com/forsale/sept/sawtool0901a.jpg
http://oldetoolshop.com/forsale/sept/sawtool0901b.jpg
http://oldetoolshop.com/forsale/sept/sawtool0901c.jpg
http://oldetoolshop.com/forsale/sept/sawtool0901d.jpg
THREE Stanley No 58 Nailsets Or Nail Sets. There is a No. 58-111, the
tip is 1/32", a No. 58-112, the tip is 2/32", a No. 58-113, the tip is
3/32", and they weigh 3 1/2 oz unboxed. These are in reasonably good
condition and were cleaned by someone else. There ain't much in the way
of patina. The tips and striking ends are all good. These ain't minty,
but for being used tools, they are pretty darn close. $14.00
http://oldetoolshop.com/forsale/sept/nailset0901a.jpg
http://oldetoolshop.com/forsale/sept/nailset0901b.jpg
http://oldetoolshop.com/forsale/sept/nailset0901c.jpg
Heavy Blacksmith Hand Forged Hot Cold Cut Chisel. Measuring 12 13/16"
overall, the head is 7 1/2" long, the edge is 1 5/8" high, and this
weighs 4 lbs 11 oz unboxed. H F hot stamped his initials in a couple of
spots on the top and underside, so he either made this or worked with a
real bunch of tool thieves. This is in decent condition and was
cleaned. The head has some overall light patina, including some spots
of lead splash on the one side. I did dress the edge and that is good
to go. The striking end has some mushrooming, but nothing sharp. The
handle is old. That has the usual dings and stains, and there is a
little roughness at the end, but it's solid and on tight. This ain't
pretty or perfect, but it will get the job done. $19.00
http://oldetoolshop.com/forsale/sept/blacksmith0901a.jpg
http://oldetoolshop.com/forsale/sept/blacksmith0901b.jpg
http://oldetoolshop.com/forsale/sept/blacksmith0901c.jpg
http://oldetoolshop.com/forsale/sept/blacksmith0901d.jpg
Stanley No 780 3 lb Stone Mason Hammer. Measuring 10 7/16" overall, the
head is 4" long, the one face is 1 1/4" in diameter, the other is 1 3/8"
wide, 1 1/4" high, and this weighs 3 lbs 4 3/4 oz total unboxed. This
is in reasonably good condition and was cleaned. There is some light
patina on the head. Both faces are good other than some light dings.
The handle has some stains, dings, some chipping at the end, but it's
solid, and the head is on tight. This ain't pristine, but it's a
quality tool that will get the job done. $18.00
http://oldetoolshop.com/forsale/sept/hammer0905a.jpg
http://oldetoolshop.com/forsale/sept/hammer0905b.jpg
http://oldetoolshop.com/forsale/sept/hammer0905c.jpg
http://oldetoolshop.com/forsale/sept/hammer0905d.jpg
TWO Machinist Trammel Points With 22 Inch Beam. The beam is 22 1/4"
long, the point bodies are 2 7/8" high, and this weighs 9 3/4 oz
unboxed. Not signed as to the maker. This is in good condition and was
not cleaned. There are a few light stains and scuffs, but nothing too
bad at all. The locking screws work and the points are quite pointy.
The beam is straight and is flat along the top. This ain't gotta fancy
name, but it's a solid tool that will get the job done. $25.00
http://oldetoolshop.com/forsale/sept/machinisttool0907a.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0907b.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0907c.jpg
Uncommon Boynton Patent 1873 Saw Set Or Sawset. Measuring 10 3/4" long
and this weighs 1 lb 3 1/4 oz unboxed. William Boynton of Battle Creek,
MI was granted Pat. No. 144,947 on Nov. 25, 1873 for the design of this
tool which was made by E. M. Boynton of New York, NY. This is for the
larger crosscut saws. This is in decent condition and was cleaned.
There is some light pitting and patina on the head. The jaws are good.
The depth stop screw works but does no remove completely. The joint is
good. There is a small flake in the metal starting on the side below
the patent date. The handles have some wear to the finish and some light
patina. The spring is missing a piece. This ain't pristine, but these
guys sure do not show up very often. $35.00
http://oldetoolshop.com/forsale/sept/sawset0901a.jpg
http://oldetoolshop.com/forsale/sept/sawset0901b.jpg
http://oldetoolshop.com/forsale/sept/sawset0901c.jpg
http://oldetoolshop.com/forsale/sept/sawset0901d.jpg
Neat Vintage Wooden Cased Sharpening Stone. The case is 9 7/8" long, 2
13/16" wide, 2 1/8" high, the stone is 8" long, 2" wide, 15/16" high,
and this weighs 2 lbs 3 oz total unboxed. Not signed as to the maker.
The stone is a man made one. This is in reasonably good condition and
was cleaned. The case is pine and both pieces were made from single
blocks of wood. There is some staining and dings to the finish. There
is a galvanized liner on the inside of the base. The stone is double
sided and you can see a binder or glue line looking from the side. The
fine side has a chip on the one edge, both both faces are fairly
straight looking from the ends and the sides. This ain't minty, but
it's a solid tool that will get the job done. $30.00
http://oldetoolshop.com/forsale/sept/sharpeningstone0901a.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0901b.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0901c.jpg
http://oldetoolshop.com/forsale/sept/sharpeningstone0901d.jpg
Big Forged Hacksaw Or Hack Saw. Measuring 23 1/4" overall, the blade is
a Disston power hacksaw blade and is 17 1/4" long, and this weighs 2 lbs
12 3/4 oz unboxed. Not signed as to the maker. This is in reasonably
good condition and was cleaned. There is some overall light patina, and
some scuffs on the head area left over from when this was made. The
leather handle scales have some dings and wear, but are solid and on
tight. The locking screw for the blade is good. This ain't gotta fancy
name, but it's a solid tool that will get the job done. $30.00
http://oldetoolshop.com/forsale/sept/saw0901a.jpg
http://oldetoolshop.com/forsale/sept/saw0901b.jpg
http://oldetoolshop.com/forsale/sept/saw0901c.jpg
http://oldetoolshop.com/forsale/sept/saw0901d.jpg
http://oldetoolshop.com/forsale/sept/saw0901e.jpg
http://oldetoolshop.com/forsale/sept/saw0901f.jpg
TWO Round Leather Arch Punches. One the left is a C S Osborne 3/8", on
the right is a Kraeuter 9/16", and they weigh 9 1/4 oz unboxed. These
are in reasonably good condition and were cleaned. The head on the
Osborne is good, the Kraeuter has some light patina. Both edges are
good with no dings or cracks, but the Osborne will need a quick touch
up. THe handle finish is worn on both and the striking ends have some
dings, but nothing too bad. These ain't minty, but they are quality
tools that will get the job done. $22.00
http://oldetoolshop.com/forsale/sept/leathertool0904a.jpg
http://oldetoolshop.com/forsale/sept/leathertool0904b.jpg
http://oldetoolshop.com/forsale/sept/leathertool0904c.jpg
http://oldetoolshop.com/forsale/sept/leathertool0904d.jpg
Western Black Beauty Camp Hatchet Hand Axe. Measuring 12 1/4" overall,
the head is 4 11/16" long (across the center), the edge is 3" high
(straight across), and this weighs 1 lb 13 3/4 oz unboxed. This is in
decent condition and was cleaned. There is some light pitting on both
sides of the head. The edge will need some work. The poll has some
dings and I did run a file over some sharp bits of mushrooming on the
back. The aluminum handle has some corrosion at the end and some wear
in the center, but it's solid. This ain't minty, and it sure ain't got
that kind of price tag either, but these guys sure do not show up very
often. $42.00
http://oldetoolshop.com/forsale/sept/axe0902a.jpg
http://oldetoolshop.com/forsale/sept/axe0902b.jpg
http://oldetoolshop.com/forsale/sept/axe0902c.jpg
http://oldetoolshop.com/forsale/sept/axe0902d.jpg
Vintage 15/16 Inch Arch Leather Rosette Punch. Measuring 5 3/16" long,
the cut is 15/16" in outside diameter, and this weighs 12 3/4 oz
unboxed. Not signed as to the maker. This is in reasonably good
condition and was cleaned. There is some overall frosting and light
patina. The edge feels sharp to the touch and there are no cracks that
I can see. There is some crusty on the inside. The striking end has
some mushrooming, wear and a few small checks. This ain't minty, but
it's a bunch less than buying a new one. $50.00
http://oldetoolshop.com/forsale/sept/leathertool0901a.jpg
http://oldetoolshop.com/forsale/sept/leathertool0901b.jpg
http://oldetoolshop.com/forsale/sept/leathertool0901c.jpg
Uncommon Vintage Teardrop Leather Arch Rosette Punch. Measuring 5 3/4"
long, the head is 1 9/16" high, 1 1/16" wide across the top, and this
weighs 1 lb 7 1/2 oz unboxed. Not signed as to the maker. This is in
reasonably good condition and was cleaned. There is some frosting and
wear on the body. The edge feels sharp to the touch. There is a little
crusty on the inside. The striking end has some mushrooming and wear.
This ain't perfect, but I sure ain't seen too many like this guy
around. $60.00
http://oldetoolshop.com/forsale/sept/leathertool0902a.jpg
http://oldetoolshop.com/forsale/sept/leathertool0902b.jpg
http://oldetoolshop.com/forsale/sept/leathertool0902c.jpg
http://oldetoolshop.com/forsale/sept/leathertool0902d.jpg
L S Starrett Combination Square Center Finding Head. This weighs 4 3/4
oz unboxed. This will fit the 12" and 18" Starrett squares as well as
their Brown & Sharpe cousins. This is in decent condition and was
cleaned. The finish is original but is worn around the slot area. The
outer machined edges have some frosting and light pitting. The inside
area has some frosting, but nothing too bad. The locking screw and tab
are good to go. This ain't minty, but it will get the job done. $22.00
http://oldetoolshop.com/forsale/sept/machinisttool0905a.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0905b.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0905c.jpg
Stanley SW No 921 10 Inch Sweep Brace. This weighs 2 lbs 14 1/2 oz
unboxed. Charles E. Mitchell of New Britain, CT was granted Pat. No.
1,011,227 on Dec. 12, 1911 for the design of the jaws and chuck used on
this tool. This is in reasonably good condition and was cleaned. The
plating on the arms is gone and there are some light dings and a few
spots of light patina. The plating on the chuck shell is good except
for around the jaw hole. The patent jaws and spring are good. The
enclosed ratchet works in both directions and the locked position. The
grip has some small dings. The pad has some deeper dings and there is
some wear around the edge. Both spin freely. This ain't minty, but
it's a top quality tool that will get the job done. $34.00
http://oldetoolshop.com/forsale/sept/brace0901a.jpg
http://oldetoolshop.com/forsale/sept/brace0901b.jpg
http://oldetoolshop.com/forsale/sept/brace0901c.jpg
http://oldetoolshop.com/forsale/sept/brace0901d.jpg
Hand Forged From A File Saw Setting Wrest. Measuring 7 3/4" long and
this weighs 5 oz unboxed. Not signed as to the maker. This is in
decent condition and was cleaned. There is some light patina and a few
spots of light pitting. The center groove has some wear, but the others
are good. This ain't perfect, but these tools made from old files are
good collectibles. $19.00
http://oldetoolshop.com/forsale/sept/hfsawwrest0901a.jpg
http://oldetoolshop.com/forsale/sept/hfsawwrest0901b.jpg
http://oldetoolshop.com/forsale/sept/hfsawwrest0901c.jpg
Foster Aluminum Stanley 101 Style Model Makers Block Plane. This weighs
2 oz unboxed. This is in reasonably good condition and was cleaned.
Aluminum body planes rarely age well. The sides have some light funky.
The sole has some machining marks and a couple of areas of light
corrosion. The cap is a bit rough, but it works as does the screw. The
blade is clean on the face and there is lots there to work with. This
ain't minty, but these guys sure do not show up very often. $20.00
http://oldetoolshop.com/forsale/sept/fosterplane0901a.jpg
http://oldetoolshop.com/forsale/sept/fosterplane0901b.jpg
http://oldetoolshop.com/forsale/sept/fosterplane0901c.jpg
http://oldetoolshop.com/forsale/sept/fosterplane0901d.jpg
Vintage Hand Forged XX Name Stamp. Measuring 3 3/16" long, the figure
is 1/4" high, and this weighs 4 1/4 oz unboxed. Not signed as to the
maker. This is in decent condition and was cleaned. At some point
there was another X and a smaller Y dressed off of the figure, but
what's left is good. The body has some light patina. There is some
mushrooming on the striking end and I did rule a file over the sharp
areas. This ain't perfect, but these guys are sure getting few and far
between of late. $16.00
http://oldetoolshop.com/forsale/sept/namestamp0901a.jpg
http://oldetoolshop.com/forsale/sept/namestamp0901b.jpg
Vintage Wood Lead Beater Smoother. Measuring 14" overall, the face is
8" long, 1 13/16" wide, and this weighs 15 oz unboxed. Not signed as to
the maker. This is in decent condition and was cleaned. The wood is
maple. Whatever this was finished with turned orange over the years and
didn't want to come off. The face has some dings, wear, and there is a
small chip on the one front corner. The handle is good other than the
staining. This ain't minty, but these guys got used hard and rarely
show up in much better shape. $25.00
http://oldetoolshop.com/forsale/aug/leadtool0901a.jpg
http://oldetoolshop.com/forsale/aug/leadtool0901b.jpg
http://oldetoolshop.com/forsale/aug/leadtool0901c.jpg
----------------------------------------
"I am not so think as you drunk I am."
Major Margaret Houlihan (M.A.S.H,)
Tony
Olde River Hard Goods
http://www.oldetoolshop.com
TSMusic on Facebook
http://www.facebook.com/tonyseomusic
//
|
